www.lovefords.org is readers supported and a participant of the Amazon Affiliate program. We may earn a small commission form any successful purchase, for more details

Ford Backup Sensors Troubleshooting: 4 Steps Procedure with Details

Backup cameras have become quite an integral part of all the vehicle because of the number of advantages they offer. With their popularity and frequent use, you can also see your Ford backup sensors troubleshooting at certain times.

Backup sensors or cameras provide excellent assistance while reversing and helps prevent accidents along with helping in reversing and parking.

As they have become an integral auto part, you can see various backup cameras in the market. But even with the most reliable brands, you can still encounter some Ford expedition backup camera problems that are easy to resolve in most cases.

If your Ford F150 backup camera is not working, you can detect it through the sensor kit and follow different troubleshooting methods to get rid of all the ford backup camera problems.

Below, we have made a whole guide with troubleshooting methods if your Ford expedition backup camera is not working.

Starting from the types of sensors to the problems caused by them, we have listed each and every detail about the backup sensors and cameras for you.

Ford Backup Sensor Kit

A backup sensor kit is responsible for warning you about any hindrances while reversing your car that ensures safer parking and no accidents.

These sensors get activated whenever you put your car in reverse and display the rearview through an LCD. This LCD pictures all the obstacles in your path and helps you park or reverse safely.

Working of a Ford Backup Sensor Kit

There are two different types of sensor kits or proximity sensors. Let’s discuss the working of both of them separately.

Ultrasonic Proximity Sensors

As ultrasonic proximity sensors use high-frequency sound waves, they are usually connected to an alarm system that goes off whenever there is any obstacle in the rear pathway.

The sound made by the alarm is responsible for warning the driver about the obstacles in the rear pathway.

Sound pulses are emitted by these sensors when any object is in the pathway, which is detected by a receiver that calculates the distance of the object from the vehicle.

Electromagnetic proximity Sensors

Electromagnetic proximity sensors use electromagnetic frequencies that help in detecting nearby obstacles and objects while reversing the car.

Moreover, they have the capacity and range to detect more objects than the ultrasonic proximity sensors. For visual aid in parking or reversing, these sensors can also be connected to a camera that provides the driver with visualization of the obstacles.

Ford Backup Sensors Troubleshooting

If your Ford F150 backup camera is not working, there can be various reasons behind that.

However, these issues are usually quite minor and can be troubleshot and solved immediately without much effort. Below we have mentioned some of the major troubleshooting methods that can help you resolve your Ford backup camera problems.

Step 1: Cleaning the Camera/sensor

As the backup cameras and sensors are closer to the road or ground, they more than likely are affected by dirt, mud, and even water.

Therefore, if your Ford expedition backup camera is not working properly, there can be a chance that you might have a dirty backup camera.

Problems caused by dirt/mud on the camera

Backup cameras aid in parking and reversing, so it is necessary that it provides a clear image of the obstacles in the rear pathway.

Dirty sensors cannot work properly. And if your backup camera is covered in dirt or mud, it won’t provide you with a high-quality clear image that will cause problems while reversing the vehicle.

Method of Cleaning

The cleaning method of the backup camera or sensors is very simple. You will require a soft cloth to wipe any dirt residues, mud, or water from the backup camera or sensor.

Step 2: Check Out for the Sound of the Sensor

Various Ford expedition backup camera problems can be due to a default in the wiring connection or the wires.

And in the case of sensors, the weak connection can be the reason. The solution of problems caused by the connections can also be solved easily.

Connection problems

The poor or damaged connection can lead to various Ford backup camera problems, including a distorted or colorless image.

Connection problems can also lead to reversing sensors not working at all. If you are experiencing any such problems, check the connection and listen for the sensors.

Solving the connection problems

If you are facing any of the issues related to the connection of your backup camera, check the connections and wiring to see if they are in the right place.

Moreover, if there is any damage to the wiring, fix it immediately for better backup camera performance. Go to the rear of your car and listen to the sensors to check if they are working properly.

Buzzing sound ensures the proper working of the sensors.

Step 3: Check for the Error Codes

While using a reversing sensor kit, you might experience some problems caused by certain glitches in the system or a disconnected power cable.

Such problems can lead to false alarms that happen quite frequently and certain errors.

Problems caused by glitches

If your completely fine working sensors have started to show a ‘no signal’ sign or any sign representing disconnection or false alarms, now is the time to look for the error code and solve the issue.

Hunting through the error codes and solving the issue

All the glitches can be easily solved by determining the error code showing up on your vehicle.

Using the manufacturer’s manual, you can hunt through the error codes to see which one is being displayed on your vehicle and then solve the issue accordingly. Either solve it yourself if you can or take it to the mechanic.  

Step 4: Ensure kit’s Perfect Installation

If your Ford f150 backup camera is not working, there can be a chance that there is a problem with your backup kit’s installation. Such problems are also quite simple to resolve.

Problematic Installation

If your backup camera doesn’t turn on as soon as you put your vehicle in the reverse gear, there can be some problem with installing the backup kit. Moreover, the loose wiring can also lead to problems

Checking the Installation

Therefore, if you face any of the problems mentioned above, check out that your backup kit is installed and set up perfectly. Checking the installation can be done concerning the manual instructions provided by the supplier.

Ford Reverse Sensing System Problems

Ford expedition backup camera not working can be justified by some sensing problems caused by the system.

Even though you can observe certain problems with the reverse sensing system, they are still simple to detect and resolve. The most frequently complained reverse sensing system problems are as follow;

Continuous Beeping

As the backup sensor kits are installed in the rear of the vehicle, there is a chance that they are installed very close to the ground.

In such a case, you will experience beeping from the sensors as they will continue to detect the ground or the road as the obstacle in your pathway.

Solution

Try to install the backup sensor at a safe distance from the road to avoid this continuous beeping.

The average distance between the sensor kit and the road is almost 18 inches to 24 inches. With this safe distance maintained, the sensor will not detect the ground as an obstacle, and the continuous beeping would stop immediately.

Distorted Image / False Alarms

Many cases are observed where the display image is distorted, unclear, or grainy. The image issues can be due to two different reasons;

Poor Connection/signals

If you are experiencing Ford expedition backup camera problems in particularly image display, poor wireless connection or wired connection can be a reason.

It can also lead to false alarms by the sensors as they won’t be receiving proper signals.

Solution

To avoid such distortion in the image, check for the connection and fix it for a clearer image for the camera and avoid the sensors’ false alarms.

Dirty Camera

In backup cameras, dirt or mud can lead to blurry and grainy images on the monitor. This is also a major reverse sensing issue. As in sensors, the false alarm occurs; in the cameras, the poor image does.

Solution

Simple grab a soft cloth and wipe all the dirt or mud from the camera for a clear image on the monitor.

System Doesn’t Respond in the Reverse Gear

Most of the reverse sensing systems are automatically turned on when the vehicle is put in reverse gear. Therefore, if your Ford expedition backup camera is not working in reverse gear, there can be certain issues.

Not connected to the system properly

In most cases, when the reverse sensing system doesn’t automatically turn on, there can be a problem with the system’s connection.

Solution

Check out that the power cables are connected to the reverse lights of your vehicle properly.

FAQs Related to Ford Backup Sensors Troubleshooting

How do you test a Ford backup sensor? Without starting your vehicle, unlock the steering Colum by turning the key to the first position.

Now shift the car into reverse while pressing on the brake. After this, you will have to move to the rear of your car and hear all the sensors separately to check if they are working. The working sensors will make a buzzing sound.

Why is my reverse sensor beeping

The reverse sensors make a beeping or buzzing sound when placed too close to the ground or road.

The sensor makes such sound to warn the driver about the nearby objects, which is the ground itself. To make sure that your sensor works properly without such noise, install it above the ground over 18 to 24 inches.

How do you clean backup sensors

Use soapy water and a soft cloth for the cleaning purpose of the backup sensors of your vehicle; make sure to not rub with a lot of force to avoid any damage.

Moreover, if there are stubborn mud stains on the camera, you can clean them by using a soft bristle brush but not scratch them.

Why does my reverse sensor not work

Various reasons lead to the poor or no working of the backup cameras. It can be due to dirt on the camera, poor signals or connection, a blown fuse, imperfect installation, and many more reasons.

Can I paint reverse sensors?

The reverse sensors that are already painted will not bear another layer of new paint.

If you want a sensor with perfect new paint, you will have to buy a new one. Some of the aftermarket sensors support paint, and you can follow the manual instructions to do so.

How much does it cost to install backup sensors?

Backup sensors come in various price ranges, but the average price range is about $261 to $269, excluding the labor charges required for the installation of these backup cameras into your vehicle.

Can you install backup sensors?

Most of the vehicles today come with backup sensors, but you can still change them and install the new ones.

Backup sensors are pretty easy to install; you will just have to drill some holes in the front and rear bumpers to ensure the perfect fitting of the backup sensors.

Which is the best reversing camera or sensors?

Reversing cameras have proved to be more successful because of the display they offer. 

Conclusion

Backup sensors and cameras offer the same functions of warning the driver about any obstacles in the rear pathway.

No matter how efficient cameras or sensors you install in your vehicle, you will still have to do some Ford backup sensors troubleshooting. Many problems can be observed on backup sensors, but most of them are easy to solve.

While Ford backup sensors troubleshooting, try to detect the problem accurately so that you won’t add to your reversing sensors’ issues.

Backup kits are no doubt extremely important, and even though with their issue, you will have to install them and manage them no matter what.

Leave a Comment